SX1282 Class Reference
Derived class for SX1282 modules. More...
#include <SX1282.h>
Inheritance diagram for SX1282:
Public Member Functions | |
| SX1282 (Module *mod) | |
| Default constructor. More... | |
 Public Member Functions inherited from SX1280 | |
| SX1280 (Module *mod) | |
| Default constructor. More... | |
| int16_t | range (bool master, uint32_t addr, uint16_t calTable[3][6]=NULL) |
| Blocking ranging method. More... | |
| int16_t | startRanging (bool master, uint32_t addr, uint16_t calTable[3][6]=NULL) |
| Interrupt-driven ranging method. More... | |
| float | getRangingResult () |
| Gets ranging result of the last ranging exchange. More... | |
| Public Member Functions inherited from SX1281 | |
| SX1281 (Module *mod) | |
| Default constructor. More... | |
| Public Member Functions inherited from SX128x | |
| SX128x (Module *mod) | |
| Default constructor. More... | |
| int16_t | begin (float freq=2400.0, float bw=812.5, uint8_t sf=9, uint8_t cr=7, uint8_t syncWord=RADIOLIB_SX128X_SYNC_WORD_PRIVATE, int8_t pwr=10, uint16_t preambleLength=12) |
| Initialization method for LoRa modem. More... | |
| int16_t | beginGFSK (float freq=2400.0, uint16_t br=800, float freqDev=400.0, int8_t pwr=10, uint16_t preambleLength=16) |
| Initialization method for GFSK modem. More... | |
| int16_t | beginBLE (float freq=2400.0, uint16_t br=800, float freqDev=400.0, int8_t pwr=10, uint8_t dataShaping=RADIOLIB_SHAPING_0_5) |
| Initialization method for BLE modem. More... | |
| int16_t | beginFLRC (float freq=2400.0, uint16_t br=650, uint8_t cr=3, int8_t pwr=10, uint16_t preambleLength=16, uint8_t dataShaping=RADIOLIB_SHAPING_0_5) |
| Initialization method for FLRC modem. More... | |
| int16_t | reset (bool verify=true) |
| Reset method. Will reset the chip to the default state using RST pin. More... | |
| int16_t | transmit (const uint8_t *data, size_t len, uint8_t addr=0) override |
| Blocking binary transmit method. Overloads for string-based transmissions are implemented in PhysicalLayer. More... | |
| int16_t | receive (uint8_t *data, size_t len) override |
| Blocking binary receive method. Overloads for string-based transmissions are implemented in PhysicalLayer. More... | |
| int16_t | transmitDirect (uint32_t frf=0) override |
| Starts direct mode transmission. More... | |
| int16_t | receiveDirect () override |
| Starts direct mode reception. Only implemented for PhysicalLayer compatibility, as SX128x series does not support direct mode reception. Will always return RADIOLIB_ERR_UNKNOWN. More... | |
| int16_t | scanChannel () override |
| Performs scan for LoRa transmission in the current channel. Detects both preamble and payload. More... | |
| int16_t | scanChannel (const ChannelScanConfig_t &config) override |
| Performs scan for LoRa transmission in the current channel. Detects both preamble and payload. More... | |
| int16_t | sleep () override |
| Sets the module to sleep mode. To wake the device up, call standby(). Overload for PhysicalLayer compatibility. More... | |
| int16_t | sleep (bool retainConfig) |
| Sets the module to sleep mode. To wake the device up, call standby(). More... | |
| int16_t | standby () override |
| Sets the module to standby mode (overload for PhysicalLayer compatibility, uses 13 MHz RC oscillator). More... | |
| int16_t | standby (uint8_t mode, bool wakeup=false) |
| Sets the module to standby mode. More... | |
| void | setDio1Action (void(*func)(void)) |
| Sets interrupt service routine to call when DIO1 activates. More... | |
| void | clearDio1Action () |
| Clears interrupt service routine to call when DIO1 activates. | |
| void | setPacketReceivedAction (void(*func)(void)) override |
| Sets interrupt service routine to call when a packet is received. More... | |
| void | clearPacketReceivedAction () override |
| Clears interrupt service routine to call when a packet is received. | |
| void | setPacketSentAction (void(*func)(void)) override |
| Sets interrupt service routine to call when a packet is sent. More... | |
| void | clearPacketSentAction () override |
| Clears interrupt service routine to call when a packet is sent. | |
| int16_t | startTransmit (const uint8_t *data, size_t len, uint8_t addr=0) override |
| Interrupt-driven binary transmit method. Overloads for string-based transmissions are implemented in PhysicalLayer. More... | |
| int16_t | finishTransmit () override |
| Clean up after transmission is done. More... | |
| int16_t | startReceive () override |
| Interrupt-driven receive method with default parameters. Implemented for compatibility with PhysicalLayer. More... | |
| int16_t | startReceive (uint16_t timeout, RadioLibIrqFlags_t irqFlags=RADIOLIB_IRQ_RX_DEFAULT_FLAGS, RadioLibIrqFlags_t irqMask=RADIOLIB_IRQ_RX_DEFAULT_MASK, size_t len=0) |
| Interrupt-driven receive method. DIO1 will be activated when full packet is received. More... | |
| uint16_t | getIrqStatus () |
| Reads the current IRQ status. More... | |
| int16_t | readData (uint8_t *data, size_t len) override |
| Reads data received after calling startReceive method. When the packet length is not known in advance, getPacketLength method must be called BEFORE calling readData! More... | |
| uint32_t | getIrqFlags () override |
| Read currently active IRQ flags. More... | |
| int16_t | setIrqFlags (uint32_t irq) override |
| Set interrupt on DIO1 to be sent on a specific IRQ bit (e.g. RxTimeout, CadDone). More... | |
| int16_t | clearIrqFlags (uint32_t irq) override |
| Clear interrupt on a specific IRQ bit (e.g. RxTimeout, CadDone). More... | |
| int16_t | startChannelScan () override |
| Interrupt-driven channel activity detection method. DIO1 will be activated when LoRa preamble is detected, or upon timeout. More... | |
| int16_t | startChannelScan (const ChannelScanConfig_t &config) override |
| Interrupt-driven channel activity detection method. DIO1 will be activated when LoRa preamble is detected, or upon timeout. More... | |
| int16_t | getChannelScanResult () override |
| Read the channel scan result. More... | |
| int16_t | setFrequency (float freq) override |
| Sets carrier frequency. Allowed values are in range from 2400.0 to 2500.0 MHz. More... | |
| int16_t | setBandwidth (float bw) |
| Sets LoRa bandwidth. Allowed values are 203.125, 406.25, 812.5 and 1625.0 kHz. More... | |
| int16_t | setSpreadingFactor (uint8_t sf) |
| Sets LoRa spreading factor. Allowed values range from 5 to 12. More... | |
| int16_t | setCodingRate (uint8_t cr, bool longInterleaving=false) |
| Sets LoRa coding rate denominator. Allowed values range from 5 to 8. More... | |
| int16_t | setOutputPower (int8_t pwr) override |
| Sets output power. Allowed values are in range from -18 to 13 dBm. More... | |
| int16_t | checkOutputPower (int8_t pwr, int8_t *clipped) override |
| Check if output power is configurable. More... | |
| int16_t | setModem (ModemType_t modem) override |
| Set modem for the radio to use. Will perform full reset and reconfigure the radio using its default parameters. More... | |
| int16_t | getModem (ModemType_t *modem) override |
| Get modem currently in use by the radio. More... | |
| int16_t | setPreambleLength (uint32_t preambleLength) |
| Sets preamble length for currently active modem. Allowed values range from 1 to 65535. More... | |
| int16_t | setDataRate (DataRate_t dr) override |
| Set data rate. More... | |
| int16_t | setBitRate (float br) override |
| Sets FSK or FLRC bit rate. Allowed values are 125, 250, 400, 500, 800, 1000, 1600 and 2000 kbps (for FSK modem) or 260, 325, 520, 650, 1000 and 1300 (for FLRC modem). More... | |
| int16_t | setFrequencyDeviation (float freqDev) override |
| Sets FSK frequency deviation. Allowed values range from 0.0 to 3200.0 kHz. More... | |
| int16_t | setDataShaping (uint8_t sh) override |
| Sets time-bandwidth product of Gaussian filter applied for shaping. Allowed values are RADIOLIB_SHAPING_0_5 or RADIOLIB_SHAPING_1_0. Set to RADIOLIB_SHAPING_NONE to disable data shaping. More... | |
| int16_t | setSyncWord (const uint8_t *syncWord, uint8_t len) |
| Sets FSK/FLRC sync word in the form of array of up to 5 bytes (FSK). For FLRC modem, the sync word must be exactly 4 bytes long. More... | |
| int16_t | setSyncWord (uint8_t syncWord, uint8_t controlBits=0x44) |
| Sets LoRa sync word. More... | |
| int16_t | setCRC (uint8_t len, uint32_t initial=0x1D0F, uint16_t polynomial=0x1021) |
| Sets CRC configuration. More... | |
| int16_t | setWhitening (bool enabled) |
| Sets whitening parameters, not available for LoRa or FLRC modem. More... | |
| int16_t | setAccessAddress (uint32_t addr) |
| Sets BLE access address. More... | |
| int16_t | setHighSensitivityMode (bool enable) |
| Enables or disables receiver high sensitivity mode. More... | |
| int16_t | setGainControl (uint8_t gain=0) |
| Enables or disables receiver manual gain control. More... | |
| float | getRSSI () override |
| Gets RSSI (Recorded Signal Strength Indicator) of the last received packet. More... | |
| float | getRSSI (bool packet) |
| Gets RSSI (Recorded Signal Strength Indicator). More... | |
| float | getSNR () override |
| Gets SNR (Signal to Noise Ratio) of the last received packet. Only available for LoRa or ranging modem. More... | |
| float | getFrequencyError () |
| Gets frequency error of the latest received packet. More... | |
| size_t | getPacketLength (bool update=true) override |
| Query modem for the packet length of received payload. More... | |
| size_t | getPacketLength (bool update, uint8_t *offset) |
| Query modem for the packet length of received payload and Rx buffer offset. More... | |
| RadioLibTime_t | getTimeOnAir (size_t len) override |
| Get expected time-on-air for a given size of payload. More... | |
| int16_t | implicitHeader (size_t len) |
| Set implicit header mode for future reception/transmission. More... | |
| int16_t | explicitHeader () |
| Set explicit header mode for future reception/transmission. More... | |
| int16_t | setEncoding (uint8_t encoding) override |
| Sets transmission encoding. Serves only as alias for PhysicalLayer compatibility. More... | |
| void | setRfSwitchPins (uint32_t rxEn, uint32_t txEn) |
Some modules contain external RF switch controlled by pins. This function gives RadioLib control over those pins to automatically switch between various modes: When idle both pins will be LOW, during TX the txEn pin will be HIGH, during RX the rxPin will be HIGH. More... | |
| void | setRfSwitchTable (const uint32_t(&pins)[Module::RFSWITCH_MAX_PINS], const Module::RfSwitchMode_t table[]) |
| Some modules contain external RF switch controlled by pins. This function gives RadioLib control over those pins to automatically switch between various modes. More... | |
| uint8_t | randomByte () override |
| Dummy random method, to ensure PhysicalLayer compatibility. More... | |
| int16_t | invertIQ (bool enable) override |
| Enable/disable inversion of the I and Q signals. More... | |
| void | setDirectAction (void(*func)(void)) override |
| Dummy method, to ensure PhysicalLayer compatibility. More... | |
| void | readBit (uint32_t pin) override |
| Dummy method, to ensure PhysicalLayer compatibility. More... | |
| int16_t | transmit (const char *str, uint8_t addr=0) |
| C-string transmit method. More... | |
| virtual int16_t | transmit (const uint8_t *data, size_t len, uint8_t addr=0) |
| Binary transmit method. Must be implemented in module class. More... | |
| virtual int16_t | receive (uint8_t *data, size_t len) |
| Binary receive method. Must be implemented in module class. More... | |
| int16_t | startTransmit (const char *str, uint8_t addr=0) |
| Interrupt-driven Arduino String transmit method. Unlike the standard transmit method, this one is non-blocking. Interrupt pin will be activated when transmission finishes. More... | |
| virtual int16_t | startTransmit (const uint8_t *data, size_t len, uint8_t addr=0) |
| Interrupt-driven binary transmit method. More... | |
| virtual int16_t | readData (uint8_t *data, size_t len) |
| Reads data that was received after calling startReceive method. More... | |
| Public Member Functions inherited from PhysicalLayer | |
| PhysicalLayer (float step, size_t maxLen) | |
| Default constructor. More... | |
| int16_t | transmit (const char *str, uint8_t addr=0) |
| C-string transmit method. More... | |
| virtual int16_t | standby (uint8_t mode) |
| Sets module to a specific standby mode. More... | |
| virtual int16_t | startReceive (uint32_t timeout, RadioLibIrqFlags_t irqFlags, RadioLibIrqFlags_t irqMask, size_t len) |
| Interrupt-driven receive method. A DIO pin will be activated when full packet is received. Must be implemented in module class. More... | |
| int16_t | startTransmit (const char *str, uint8_t addr=0) |
| Interrupt-driven Arduino String transmit method. Unlike the standard transmit method, this one is non-blocking. Interrupt pin will be activated when transmission finishes. More... | |
| virtual int16_t | setSyncWord (uint8_t *sync, size_t len) |
| Set sync word. Must be implemented in module class if the module supports it. More... | |
| virtual int16_t | setPreambleLength (size_t len) |
| Set preamble length. Must be implemented in module class if the module supports it. More... | |
| virtual int16_t | checkDataRate (DataRate_t dr) |
| Check the data rate can be configured by this module. Must be implemented in module class if the module supports it. More... | |
| float | getFreqStep () const |
| Gets the module frequency step size that was set in constructor. More... | |
| virtual RadioLibTime_t | calculateRxTimeout (RadioLibTime_t timeoutUs) |
| Calculate the timeout value for this specific module / series (in number of symbols or units of time). More... | |
| uint32_t | getIrqMapped (RadioLibIrqFlags_t irq) |
| Convert from radio-agnostic IRQ flags to radio-specific flags. More... | |
| int16_t | checkIrq (RadioLibIrqType_t irq) |
| Check whether a specific IRQ bit is set (e.g. RxTimeout, CadDone). More... | |
| int16_t | setIrq (RadioLibIrqFlags_t irq) |
| Set interrupt on specific IRQ bit(s) (e.g. RxTimeout, CadDone). Keep in mind that not all radio modules support all RADIOLIB_IRQ_ flags! More... | |
| int16_t | clearIrq (RadioLibIrqFlags_t irq) |
| Clear interrupt on a specific IRQ bit (e.g. RxTimeout, CadDone). Keep in mind that not all radio modules support all RADIOLIB_IRQ_ flags! More... | |
| int32_t | random (int32_t max) |
| Get truly random number in range 0 - max. More... | |
| int32_t | random (int32_t min, int32_t max) |
| Get truly random number in range min - max. More... | |
| int16_t | startDirect () |
| Configure module parameters for direct modes. Must be called prior to "ham" modes like RTTY or AX.25. Only available in FSK mode. More... | |
| int16_t | setDirectSyncWord (uint32_t syncWord, uint8_t len) |
| Set sync word to be used to determine start of packet in direct reception mode. More... | |
| int16_t | available () |
| Get the number of direct mode bytes currently available in buffer. More... | |
| void | dropSync () |
| Forcefully drop synchronization. | |
| uint8_t | read (bool drop=true) |
| Get data from direct mode buffer. More... | |
| virtual int16_t | setDIOMapping (uint32_t pin, uint32_t value) |
| Configure DIO pin mapping to get a given signal on a DIO pin (if available). More... | |
| virtual void | setChannelScanAction (void(*func)(void)) |
| Sets interrupt service routine to call when a channel scan is finished. More... | |
| virtual void | clearChannelScanAction () |
| Clears interrupt service routine to call when a channel scan is finished. | |
Detailed Description
Derived class for SX1282 modules.
Constructor & Destructor Documentation
◆ SX1282()
| SX1282::SX1282 | ( | Module * | mod | ) |
The documentation for this class was generated from the following files:
- src/modules/SX128x/SX1282.h
- src/modules/SX128x/SX1282.cpp
