Derived class for STM32WL modules. More...

#include <STM32WLx.h>

Inheritance diagram for STM32WLx:

Public Types
enum	OpMode_t { MODE_END_OF_TABLE = Module::MODE_END_OF_TABLE , MODE_IDLE = Module::MODE_IDLE , MODE_RX = Module::MODE_RX , MODE_TX_LP = Module::MODE_TX , MODE_TX_HP }
	Custom operation modes for STMWLx. More...

Public Member Functions
	STM32WLx (STM32WLx_Module *mod)
	Default constructor. More...

int16_t	begin (float freq=434.0, float bw=125.0, uint8_t sf=9, uint8_t cr=7, uint8_t syncWord=RADIOLIB_SX126X_SYNC_WORD_PRIVATE, int8_t power=10, uint16_t preambleLength=8, float tcxoVoltage=1.6, bool useRegulatorLDO=false)
	Initialization method for LoRa modem. More...

int16_t	beginFSK (float freq=434.0, float br=4.8, float freqDev=5.0, float rxBw=156.2, int8_t power=10, uint16_t preambleLength=16, float tcxoVoltage=1.6, bool useRegulatorLDO=false)
	Initialization method for FSK modem. More...

virtual int16_t	setOutputPower (int8_t power) override
	Sets output power. Allowed values are in range from -17 to 22 dBm. More...

void	setDio1Action (void(*func)(void))
	Sets interrupt service routine to call when DIO1/2/3 activates. More...

void	clearDio1Action ()
	Clears interrupt service routine to call when DIO1/2/3 activates.

void	setPacketReceivedAction (void(*func)(void)) override
	Sets interrupt service routine to call when a packet is received. More...

void	clearPacketReceivedAction () override
	Clears interrupt service routine to call when a packet is received.

void	setPacketSentAction (void(*func)(void)) override
	Sets interrupt service routine to call when a packet is sent. More...

void	clearPacketSentAction () override
	Clears interrupt service routine to call when a packet is sent.

void	setChannelScanAction (void(*func)(void)) override
	Sets interrupt service routine to call when a channel scan is finished. More...

void	clearChannelScanAction () override
	Clears interrupt service routine to call when a channel scan is finished.

void	setRfSwitchTable (const uint32_t(&pins)[Module::RFSWITCH_MAX_PINS], const Module::RfSwitchMode_t table[])
	Some modules contain external RF switch controlled by pins. This function gives RadioLib control over those pins to automatically switch between various modes. More...

Public Member Functions inherited from SX1262
	SX1262 (Module *mod)
	Default constructor. More...

int16_t	begin (float freq=434.0, float bw=125.0, uint8_t sf=9, uint8_t cr=7, uint8_t syncWord=RADIOLIB_SX126X_SYNC_WORD_PRIVATE, int8_t power=10, uint16_t preambleLength=8, float tcxoVoltage=1.6, bool useRegulatorLDO=false)
	Initialization method for LoRa modem. More...

int16_t	beginFSK (float freq=434.0, float br=4.8, float freqDev=5.0, float rxBw=156.2, int8_t power=10, uint16_t preambleLength=16, float tcxoVoltage=1.6, bool useRegulatorLDO=false)
	Initialization method for FSK modem. More...

int16_t	beginLRFHSS (float freq=434.0, uint8_t bw=RADIOLIB_SX126X_LR_FHSS_BW_722_66, uint8_t cr=RADIOLIB_SX126X_LR_FHSS_CR_2_3, bool narrowGrid=true, int8_t power=10, float tcxoVoltage=1.6, bool useRegulatorLDO=false)
	Initialization method for LR-FHSS modem. This modem only supports transmission! More...

int16_t	setFrequency (float freq) override
	Sets carrier frequency. Allowed values are in range from 150.0 to 960.0 MHz. Will automatically perform image calibration if the frequency changes by more than RADIOLIB_SX126X_CAL_IMG_FREQ_TRIG MHz. More...

int16_t	setFrequency (float freq, bool skipCalibration)
	Sets carrier frequency. Allowed values are in range from 150.0 to 960.0 MHz. Will automatically perform image calibration if the frequency changes by more than RADIOLIB_SX126X_CAL_IMG_FREQ_TRIG_MHZ. More...

int16_t	checkOutputPower (int8_t power, int8_t *clipped) override
	Check if output power is configurable. More...

int16_t	setModem (ModemType_t modem) override
	Set modem for the radio to use. Will perform full reset and reconfigure the radio using its default parameters. More...

Public Member Functions inherited from SX126x
	SX126x (Module *mod)
	Default constructor. More...

int16_t	begin (uint8_t cr, uint8_t syncWord, uint16_t preambleLength, float tcxoVoltage, bool useRegulatorLDO=false)
	Initialization method for LoRa modem. More...

int16_t	beginFSK (float br, float freqDev, float rxBw, uint16_t preambleLength, float tcxoVoltage, bool useRegulatorLDO=false)
	Initialization method for FSK modem. More...

int16_t	beginLRFHSS (uint8_t bw, uint8_t cr, bool narrowGrid, float tcxoVoltage, bool useRegulatorLDO=false)
	Initialization method for LR-FHSS modem. This modem only supports transmission! More...

int16_t	setLrFhssConfig (uint8_t bw, uint8_t cr, uint8_t hdrCount=3, uint16_t hopSeqId=0x100)
	Sets LR-FHSS configuration. More...

int16_t	reset (bool verify=true)
	Reset method. Will reset the chip to the default state using RST pin. More...

int16_t	transmit (const uint8_t *data, size_t len, uint8_t addr=0) override
	Blocking binary transmit method. Overloads for string-based transmissions are implemented in PhysicalLayer. More...

int16_t	receive (uint8_t *data, size_t len) override
	Blocking binary receive method. Overloads for string-based transmissions are implemented in PhysicalLayer. More...

int16_t	transmitDirect (uint32_t frf=0) override
	Starts direct mode transmission. More...

int16_t	receiveDirect () override
	Starts direct mode reception. Only implemented for PhysicalLayer compatibility, as SX126x series does not support direct mode reception. Will always return RADIOLIB_ERR_UNKNOWN. More...

int16_t	scanChannel () override
	Performs scan for LoRa transmission in the current channel. Detects both preamble and payload. Configuration defaults to the values recommended by AN1200.48. More...

int16_t	scanChannel (const ChannelScanConfig_t &config) override
	Performs scan for LoRa transmission in the current channel. Detects both preamble and payload. More...

int16_t	sleep () override
	Sets the module to sleep mode. To wake the device up, call standby(). Overload with warm start enabled for PhysicalLayer compatibility. More...

int16_t	sleep (bool retainConfig)
	Sets the module to sleep mode. To wake the device up, call standby(). More...

int16_t	standby () override
	Sets the module to standby mode (overload for PhysicalLayer compatibility, uses 13 MHz RC oscillator). More...

int16_t	standby (uint8_t mode, bool wakeup=true)
	Sets the module to standby mode. More...

void	setDio1Action (void(*func)(void))
	Sets interrupt service routine to call when DIO1 activates. More...

void	clearDio1Action ()
	Clears interrupt service routine to call when DIO1 activates.

void	setPacketReceivedAction (void(*func)(void)) override
	Sets interrupt service routine to call when a packet is received. More...

void	clearPacketReceivedAction () override
	Clears interrupt service routine to call when a packet is received.

void	setPacketSentAction (void(*func)(void)) override
	Sets interrupt service routine to call when a packet is sent. More...

void	clearPacketSentAction () override
	Clears interrupt service routine to call when a packet is sent.

void	setChannelScanAction (void(*func)(void)) override
	Sets interrupt service routine to call when a channel scan is finished. More...

void	clearChannelScanAction () override
	Clears interrupt service routine to call when a channel scan is finished.

int16_t	startTransmit (const uint8_t *data, size_t len, uint8_t addr=0) override
	Interrupt-driven binary transmit method. Overloads for string-based transmissions are implemented in PhysicalLayer. More...

int16_t	finishTransmit () override
	Clean up after transmission is done. More...

int16_t	startReceive () override
	Interrupt-driven receive method with default parameters. Implemented for compatibility with PhysicalLayer. More...

int16_t	startReceive (uint32_t timeout, RadioLibIrqFlags_t irqFlags=RADIOLIB_IRQ_RX_DEFAULT_FLAGS, RadioLibIrqFlags_t irqMask=RADIOLIB_IRQ_RX_DEFAULT_MASK, size_t len=0)
	Interrupt-driven receive method. DIO1 will be activated when full packet is received. More...

int16_t	startReceiveDutyCycle (uint32_t rxPeriod, uint32_t sleepPeriod, RadioLibIrqFlags_t irqFlags=RADIOLIB_IRQ_RX_DEFAULT_FLAGS, RadioLibIrqFlags_t irqMask=RADIOLIB_IRQ_RX_DEFAULT_MASK)
	Interrupt-driven receive method where the device mostly sleeps and periodically wakes to listen. Note that this function assumes the unit will take 500us + TCXO_delay to change state. See datasheet section 13.1.7, version 1.2. More...

int16_t	startReceiveDutyCycleAuto (uint16_t senderPreambleLength=0, uint16_t minSymbols=8, RadioLibIrqFlags_t irqFlags=RADIOLIB_IRQ_RX_DEFAULT_FLAGS, RadioLibIrqFlags_t irqMask=RADIOLIB_IRQ_RX_DEFAULT_MASK)
	Calls startReceiveDutyCycle with rxPeriod and sleepPeriod set so the unit shouldn't miss any messages. More...

int16_t	readData (uint8_t *data, size_t len) override
	Reads data received after calling startReceive method. When the packet length is not known in advance, getPacketLength method must be called BEFORE calling readData! More...

int16_t	startChannelScan () override
	Interrupt-driven channel activity detection method. DIO1 will be activated when LoRa preamble is detected, or upon timeout. Defaults to CAD parameter values recommended by AN1200.48. More...

int16_t	startChannelScan (const ChannelScanConfig_t &config) override
	Interrupt-driven channel activity detection method. DIO1 will be activated when LoRa preamble is detected, or upon timeout. More...

int16_t	getChannelScanResult () override
	Read the channel scan result. More...

int16_t	setBandwidth (float bw)
	Sets LoRa bandwidth. Allowed values are 7.8, 10.4, 15.6, 20.8, 31.25, 41.7, 62.5, 125.0, 250.0 and 500.0 kHz. More...

int16_t	setSpreadingFactor (uint8_t sf)
	Sets LoRa spreading factor. Allowed values range from 5 to 12. More...

int16_t	setCodingRate (uint8_t cr)
	Sets LoRa coding rate denominator. Allowed values range from 5 to 8. More...

int16_t	setSyncWord (uint8_t syncWord, uint8_t controlBits=0x44)
	Sets LoRa sync word. More...

int16_t	setCurrentLimit (float currentLimit)
	Sets current protection limit. Can be set in 2.5 mA steps. More...

float	getCurrentLimit ()
	Reads current protection limit. More...

int16_t	setPreambleLength (size_t preambleLength) override
	Sets preamble length for LoRa or FSK modem. Allowed values range from 1 to 65535. More...

int16_t	setFrequencyDeviation (float freqDev) override
	Sets FSK frequency deviation. Allowed values range from 0.0 to 200.0 kHz. More...

int16_t	setBitRate (float br) override
	Sets FSK bit rate. Allowed values range from 0.6 to 300.0 kbps. More...

int16_t	setDataRate (DataRate_t dr) override
	Set data. More...

int16_t	checkDataRate (DataRate_t dr) override
	Check the data rate can be configured by this module. More...

int16_t	setRxBandwidth (float rxBw)
	Sets FSK receiver bandwidth. Allowed values are 4.8, 5.8, 7.3, 9.7, 11.7, 14.6, 19.5, 23.4, 29.3, 39.0, 46.9, 58.6, 78.2, 93.8, 117.3, 156.2, 187.2, 234.3, 312.0, 373.6 and 467.0 kHz. More...

int16_t	setRxBoostedGainMode (bool rxbgm, bool persist=true)
	Enables or disables Rx Boosted Gain mode as described in SX126x datasheet section 9.6 (SX1261/2 v2.1, SX1268 v1.1) More...

int16_t	setDataShaping (uint8_t sh) override
	Sets time-bandwidth product of Gaussian filter applied for shaping. Allowed values are RADIOLIB_SHAPING_0_3, RADIOLIB_SHAPING_0_5, RADIOLIB_SHAPING_0_7 or RADIOLIB_SHAPING_1_0. Set to RADIOLIB_SHAPING_NONE to disable data shaping. More...

int16_t	setSyncWord (uint8_t *syncWord, size_t len) override
	Sets FSK sync word in the form of array of up to 8 bytes. Can also set LR-FHSS sync word, but its length must be 4 bytes. More...

int16_t	setSyncBits (uint8_t *syncWord, uint8_t bitsLen)
	Sets FSK sync word in the form of array of up to 8 bytes. More...

int16_t	setNodeAddress (uint8_t addr)
	Sets node address. Calling this method will also enable address filtering for node address only. More...

int16_t	setBroadcastAddress (uint8_t broadAddr)
	Sets broadcast address. Calling this method will also enable address filtering for node and broadcast address. More...

int16_t	disableAddressFiltering ()
	Disables address filtering. Calling this method will also erase previously set addresses. More...

int16_t	setCRC (uint8_t len, uint16_t initial=0x1D0F, uint16_t polynomial=0x1021, bool inverted=true)
	Sets CRC configuration. More...

int16_t	setWhitening (bool enabled, uint16_t initial=0x01FF)
	Sets FSK whitening parameters. More...

int16_t	setTCXO (float voltage, uint32_t delay=5000)
	Sets TCXO (Temperature Compensated Crystal Oscillator) configuration. More...

int16_t	setDio2AsRfSwitch (bool enable=true)
	Set DIO2 to function as RF switch (default in Semtech example designs). More...

float	getDataRate () const
	Gets effective data rate for the last transmitted packet. The value is calculated only for payload bytes. More...

float	getRSSI () override
	Gets recorded signal strength indicator. Overload with packet mode enabled for PhysicalLayer compatibility. More...

float	getRSSI (bool packet)
	Gets RSSI (Recorded Signal Strength Indicator). More...

float	getSNR () override
	Gets SNR (Signal to Noise Ratio) of the last received packet. Only available for LoRa modem. More...

float	getFrequencyError ()
	Gets frequency error of the latest received packet. WARNING: This functionality is based on SX128x implementation and not documented on SX126x. While it seems to be working, it should be used with caution! More...

size_t	getPacketLength (bool update=true) override
	Query modem for the packet length of received payload. More...

size_t	getPacketLength (bool update, uint8_t *offset)
	Query modem for the packet length of received payload and Rx buffer offset. More...

int16_t	fixedPacketLengthMode (uint8_t len=RADIOLIB_SX126X_MAX_PACKET_LENGTH)
	Set modem in fixed packet length mode. Available in FSK mode only. More...

int16_t	variablePacketLengthMode (uint8_t maxLen=RADIOLIB_SX126X_MAX_PACKET_LENGTH)
	Set modem in variable packet length mode. Available in FSK mode only. More...

RadioLibTime_t	getTimeOnAir (size_t len) override
	Get expected time-on-air for a given size of payload. More...

RadioLibTime_t	calculateRxTimeout (RadioLibTime_t timeoutUs) override
	Calculate the timeout value for this specific module / series (in number of symbols or units of time) More...

uint32_t	getIrqFlags () override
	Read currently active IRQ flags. More...

int16_t	setIrqFlags (uint32_t irq) override
	Set interrupt on DIO1 to be sent on a specific IRQ bit (e.g. RxTimeout, CadDone). More...

int16_t	clearIrqFlags (uint32_t irq) override
	Clear interrupt on a specific IRQ bit (e.g. RxTimeout, CadDone). More...

int16_t	implicitHeader (size_t len)
	Set implicit header mode for future reception/transmission. More...

int16_t	explicitHeader ()
	Set explicit header mode for future reception/transmission. More...

int16_t	setRegulatorLDO ()
	Set regulator mode to LDO. More...

int16_t	setRegulatorDCDC ()
	Set regulator mode to DC-DC. More...

int16_t	setEncoding (uint8_t encoding) override
	Sets transmission encoding. Available in FSK mode only. Serves only as alias for PhysicalLayer compatibility. More...

void	setRfSwitchPins (uint32_t rxEn, uint32_t txEn)
	Some modules contain external RF switch controlled by pins. This function gives RadioLib control over those pins to automatically switch between various modes: When idle both pins will be LOW, during TX the `txEn` pin will be HIGH, during RX the `rxPin` will be HIGH. More...

void	setRfSwitchTable (const uint32_t(&pins)[Module::RFSWITCH_MAX_PINS], const Module::RfSwitchMode_t table[])
	Some modules contain external RF switch controlled by pins. This function gives RadioLib control over those pins to automatically switch between various modes. More...

int16_t	forceLDRO (bool enable)
	Forces LoRa low data rate optimization. Only available in LoRa mode. After calling this method, LDRO will always be set to the provided value, regardless of symbol length. To re-enable automatic LDRO configuration, call SX126x::autoLDRO() More...

int16_t	autoLDRO ()
	Re-enables automatic LDRO configuration. Only available in LoRa mode. After calling this method, LDRO will be enabled automatically when symbol length exceeds 16 ms. More...

uint8_t	randomByte () override
	Get one truly random byte from RSSI noise. More...

int16_t	invertIQ (bool enable) override
	Enable/disable inversion of the I and Q signals. More...

int16_t	getModem (ModemType_t *modem) override
	Get modem currently in use by the radio. More...

void	setDirectAction (void(*func)(void)) override
	Set interrupt service routine function to call when data bit is received in direct mode. More...

void	readBit (uint32_t pin) override
	Function to read and process data bit in direct reception mode. More...

int16_t	uploadPatch (const uint32_t *patch, size_t len, bool nonvolatile=true)
	Upload binary patch into the SX126x device RAM. Patch is needed to e.g., enable spectral scan and must be uploaded again on every power cycle. More...

int16_t	spectralScanStart (uint16_t numSamples, uint8_t window=RADIOLIB_SX126X_SPECTRAL_SCAN_WINDOW_DEFAULT, uint8_t interval=RADIOLIB_SX126X_SCAN_INTERVAL_8_20_US)
	Start spectral scan. Requires binary path to be uploaded. More...

void	spectralScanAbort ()
	Abort an ongoing spectral scan.

int16_t	spectralScanGetStatus ()
	Read the status of spectral scan. More...

int16_t	spectralScanGetResult (uint16_t *results)
	Read the result of spectral scan. More...

int16_t	setPaConfig (uint8_t paDutyCycle, uint8_t deviceSel, uint8_t hpMax=RADIOLIB_SX126X_PA_CONFIG_HP_MAX, uint8_t paLut=RADIOLIB_SX126X_PA_CONFIG_PA_LUT)
	Set the PA configuration. Allows user to optimize PA for a specific output power and matching network. Any calls to this method must be done after calling begin/beginFSK and/or setOutputPower. WARNING: Use at your own risk! Setting invalid values can and will lead to permanent damage! More...

int16_t	calibrateImage (float freq)
	Perform image rejection calibration for the specified frequency. Will try to use Semtech-defined presets first, and if none of them matches, custom iamge calibration will be attempted using calibrateImageRejection. More...

int16_t	calibrateImageRejection (float freqMin, float freqMax)
	Perform image rejection calibration for the specified frequency band. WARNING: Use at your own risk! Setting incorrect values may lead to decreased performance. More...

int16_t	setPaRampTime (uint8_t rampTime)
	Set PA ramp-up time. Set to 200us by default. More...

int16_t	transmit (const char *str, uint8_t addr=0)
	C-string transmit method. More...

virtual int16_t	transmit (const uint8_t *data, size_t len, uint8_t addr=0)
	Binary transmit method. Must be implemented in module class. More...

virtual int16_t	receive (uint8_t *data, size_t len)
	Binary receive method. Must be implemented in module class. More...

int16_t	startTransmit (const char *str, uint8_t addr=0)
	Interrupt-driven Arduino String transmit method. Unlike the standard transmit method, this one is non-blocking. Interrupt pin will be activated when transmission finishes. More...

virtual int16_t	startTransmit (const uint8_t *data, size_t len, uint8_t addr=0)
	Interrupt-driven binary transmit method. More...

virtual int16_t	readData (uint8_t *data, size_t len)
	Reads data that was received after calling startReceive method. More...

Public Member Functions inherited from PhysicalLayer
	PhysicalLayer (float step, size_t maxLen)
	Default constructor. More...

int16_t	transmit (const char *str, uint8_t addr=0)
	C-string transmit method. More...

virtual int16_t	standby (uint8_t mode)
	Sets module to a specific standby mode. More...

int16_t	startTransmit (const char *str, uint8_t addr=0)
	Interrupt-driven Arduino String transmit method. Unlike the standard transmit method, this one is non-blocking. Interrupt pin will be activated when transmission finishes. More...

float	getFreqStep () const
	Gets the module frequency step size that was set in constructor. More...

uint32_t	getIrqMapped (RadioLibIrqFlags_t irq)
	Convert from radio-agnostic IRQ flags to radio-specific flags. More...

int16_t	checkIrq (RadioLibIrqType_t irq)
	Check whether a specific IRQ bit is set (e.g. RxTimeout, CadDone). More...

int16_t	setIrq (RadioLibIrqFlags_t irq)
	Set interrupt on specific IRQ bit(s) (e.g. RxTimeout, CadDone). Keep in mind that not all radio modules support all RADIOLIB_IRQ_ flags! More...

int16_t	clearIrq (RadioLibIrqFlags_t irq)
	Clear interrupt on a specific IRQ bit (e.g. RxTimeout, CadDone). Keep in mind that not all radio modules support all RADIOLIB_IRQ_ flags! More...

int32_t	random (int32_t max)
	Get truly random number in range 0 - max. More...

int32_t	random (int32_t min, int32_t max)
	Get truly random number in range min - max. More...

int16_t	startDirect ()
	Configure module parameters for direct modes. Must be called prior to "ham" modes like RTTY or AX.25. Only available in FSK mode. More...

int16_t	setDirectSyncWord (uint32_t syncWord, uint8_t len)
	Set sync word to be used to determine start of packet in direct reception mode. More...

int16_t	available ()
	Get the number of direct mode bytes currently available in buffer. More...

void	dropSync ()
	Forcefully drop synchronization.

uint8_t	read (bool drop=true)
	Get data from direct mode buffer. More...

virtual int16_t	setDIOMapping (uint32_t pin, uint32_t value)
	Configure DIO pin mapping to get a given signal on a DIO pin (if available). More...

Additional Inherited Members
Public Attributes inherited from SX126x
bool	XTAL
	Whether the module has an XTAL (true) or TCXO (false). Defaults to false.

bool	standbyXOSC
	Whether to use XOSC (true) or RC (false) oscillator in standby mode. Defaults to false.

Detailed Description

Derived class for STM32WL modules.

The radio integrated into these modules is essentially the same as the Semtech SX126x external radio chips, so most of the documentation for those also applies here.

One notable difference with the SX126x radios is that this radio essentially combines the SX1261 and SX1262 by integrating both the low-power (LP) and high-power (HP) amplifier. See setOutputPower() and setRfSwitchTable() for details on how this is handled.

Member Enumeration Documentation

◆ OpMode_t

enum STM32WLx::OpMode_t

Custom operation modes for STMWLx.

This splits the TX mode into two modes: Low-power and high-power. These constants can be used with the setRfSwitchTable() method, instead of the Module::OpMode_t constants.

Enumerator
MODE_END_OF_TABLE	End of table marker, use END_OF_MODE_TABLE constant instead
MODE_IDLE	Idle mode
MODE_RX	Receive mode
MODE_TX_LP	Low power transmission mode
MODE_TX_HP	High power transmission mode

Constructor & Destructor Documentation

◆ STM32WLx()

STM32WLx::STM32WLx ( STM32WLx_Module * mod )

Default constructor.

Parameters

mod	Instance of STM32WLx_Module that will be used to communicate with the radio.

Member Function Documentation

◆ begin()

int16_t STM32WLx::begin	(	float	freq = `434.0`,
		float	bw = `125.0`,
		uint8_t	sf = `9`,
		uint8_t	cr = `7`,
		uint8_t	syncWord = `RADIOLIB_SX126X_SYNC_WORD_PRIVATE`,
		int8_t	power = `10`,
		uint16_t	preambleLength = `8`,
		float	tcxoVoltage = `1.6`,
		bool	useRegulatorLDO = `false`
	)

Initialization method for LoRa modem.

Parameters

freq	Carrier frequency in MHz. Defaults to 434.0 MHz.
bw	LoRa bandwidth in kHz. Defaults to 125.0 kHz.
sf	LoRa spreading factor. Defaults to 9.
cr	LoRa coding rate denominator. Defaults to 7 (coding rate 4/7).
syncWord	1-byte LoRa sync word. Defaults to RADIOLIB_SX126X_SYNC_WORD_PRIVATE (0x12).
power	Output power in dBm. Defaults to 10 dBm.
preambleLength	LoRa preamble length in symbols. Defaults to 8 symbols.
tcxoVoltage	TCXO reference voltage to be set on DIO3. Defaults to 1.6 V. If you are seeing -706/-707 error codes, it likely means you are using non-0 value for module with XTAL. To use XTAL, either set this value to 0, or set SX126x::XTAL to true.
useRegulatorLDO	Whether to use only LDO regulator (true) or DC-DC regulator (false). Defaults to false.

Returns: Status Codes

◆ beginFSK()

int16_t STM32WLx::beginFSK	(	float	freq = `434.0`,
		float	br = `4.8`,
		float	freqDev = `5.0`,
		float	rxBw = `156.2`,
		int8_t	power = `10`,
		uint16_t	preambleLength = `16`,
		float	tcxoVoltage = `1.6`,
		bool	useRegulatorLDO = `false`
	)

Initialization method for FSK modem.

Parameters

freq	Carrier frequency in MHz. Defaults to 434.0 MHz.
br	FSK bit rate in kbps. Defaults to 4.8 kbps.
freqDev	Frequency deviation from carrier frequency in kHz. Defaults to 5.0 kHz.
rxBw	Receiver bandwidth in kHz. Defaults to 156.2 kHz.
power	Output power in dBm. Defaults to 10 dBm.
preambleLength	FSK preamble length in bits. Defaults to 16 bits.
tcxoVoltage	TCXO reference voltage to be set on DIO3. Defaults to 1.6 V. If you are seeing -706/-707 error codes, it likely means you are using non-0 value for module with XTAL. To use XTAL, either set this value to 0, or set SX126x::XTAL to true.
useRegulatorLDO	Whether to use only LDO regulator (true) or DC-DC regulator (false). Defaults to false.

Returns: Status Codes

◆ setChannelScanAction()

void STM32WLx::setChannelScanAction ( void(*)(void) func )

overridevirtual

Sets interrupt service routine to call when a channel scan is finished.

Parameters

func	ISR to call.

Reimplemented from PhysicalLayer.

◆ setDio1Action()

void STM32WLx::setDio1Action ( void(*)(void) func )

Sets interrupt service routine to call when DIO1/2/3 activates.

Parameters

func	ISR to call.

◆ setOutputPower()

int16_t STM32WLx::setOutputPower ( int8_t power )

overridevirtual

Sets output power. Allowed values are in range from -17 to 22 dBm.

This automatically switches between the low-power (LP) and high-power (HP) amplifier.

LP is preferred and supports -17 to +14dBm. When a higher power is requested (or the LP amplifier is marked as unavailable using setRfSwitchTable()), HP is used, which supports -9 to +22dBm. If the LP is marked as unavailable, HP output will be used instead.

Parameters

power Output power to be set in dBm.

Returns: Status Codes

Reimplemented from SX1262.

◆ setPacketReceivedAction()

void STM32WLx::setPacketReceivedAction ( void(*)(void) func )

overridevirtual

Sets interrupt service routine to call when a packet is received.

Parameters

func	ISR to call.

Reimplemented from PhysicalLayer.

◆ setPacketSentAction()

void STM32WLx::setPacketSentAction ( void(*)(void) func )

overridevirtual

Sets interrupt service routine to call when a packet is sent.

Parameters

func	ISR to call.

Reimplemented from PhysicalLayer.

◆ setRfSwitchTable()

void SX126x::setRfSwitchTable

Some modules contain external RF switch controlled by pins. This function gives RadioLib control over those pins to automatically switch between various modes.

This method works like Module::setRfSwitchTable(), except that you should use STM32WLx::OpMode_t constants for modes, which distinguishes between a low-power (LP) and high-power (HP) TX mode.

For boards that do not support both modes, just omit the unsupported mode from the table and it will not be used (and the valid power range is adjusted by setOutputPower() accordingly).

Note that the setRfSwitchTable() method should be called before the begin() method, to ensure the radio knows which modes are supported during initialization.

The documentation for this class was generated from the following files:

src/modules/SX126x/STM32WLx.h
src/modules/SX126x/STM32WLx.cpp

Public Types

Public Member Functions

Additional Inherited Members

Detailed Description

Member Enumeration Documentation

◆ OpMode_t

Constructor & Destructor Documentation

◆ STM32WLx()

Member Function Documentation

◆ begin()

◆ beginFSK()

◆ setChannelScanAction()

◆ setDio1Action()

◆ setOutputPower()

◆ setPacketReceivedAction()

◆ setPacketSentAction()

◆ setRfSwitchTable()