SX1261 Class Reference
Derived class for SX1261 modules. More...
#include <SX1261.h>
Inheritance diagram for SX1261:
Public Member Functions | |
| SX1261 (Module *mod) | |
| Default constructor. More... | |
| int16_t | setOutputPower (int8_t power) override |
| Sets output power. Allowed values are in range from -17 to 15 dBm. More... | |
| int16_t | checkOutputPower (int8_t power, int8_t *clipped) override |
| Check if output power is configurable. More... | |
 Public Member Functions inherited from SX1262 | |
| SX1262 (Module *mod) | |
| Default constructor. More... | |
| int16_t | begin (float freq=434.0, float bw=125.0, uint8_t sf=9, uint8_t cr=7, uint8_t syncWord=RADIOLIB_SX126X_SYNC_WORD_PRIVATE, int8_t power=10, uint16_t preambleLength=8, float tcxoVoltage=1.6, bool useRegulatorLDO=false) |
| Initialization method for LoRa modem. More... | |
| int16_t | beginFSK (float freq=434.0, float br=4.8, float freqDev=5.0, float rxBw=156.2, int8_t power=10, uint16_t preambleLength=16, float tcxoVoltage=1.6, bool useRegulatorLDO=false) |
| Initialization method for FSK modem. More... | |
| int16_t | beginLRFHSS (float freq=434.0, uint8_t bw=RADIOLIB_SX126X_LR_FHSS_BW_722_66, uint8_t cr=RADIOLIB_SX126X_LR_FHSS_CR_2_3, bool narrowGrid=true, int8_t power=10, float tcxoVoltage=1.6, bool useRegulatorLDO=false) |
| Initialization method for LR-FHSS modem. This modem only supports transmission! More... | |
| int16_t | setFrequency (float freq) override |
| Sets carrier frequency. Allowed values are in range from 150.0 to 960.0 MHz. Will automatically perform image calibration if the frequency changes by more than RADIOLIB_SX126X_CAL_IMG_FREQ_TRIG MHz. More... | |
| int16_t | setFrequency (float freq, bool skipCalibration) |
| Sets carrier frequency. Allowed values are in range from 150.0 to 960.0 MHz. Will automatically perform image calibration if the frequency changes by more than RADIOLIB_SX126X_CAL_IMG_FREQ_TRIG_MHZ. More... | |
| int16_t | checkOutputPower (int8_t power, int8_t *clipped) override |
| Check if output power is configurable. More... | |
| int16_t | setModem (ModemType_t modem) override |
| Set modem for the radio to use. Will perform full reset and reconfigure the radio using its default parameters. More... | |
| Public Member Functions inherited from SX126x | |
| SX126x (Module *mod) | |
| Default constructor. More... | |
| int16_t | begin (uint8_t cr, uint8_t syncWord, uint16_t preambleLength, float tcxoVoltage, bool useRegulatorLDO=false) |
| Initialization method for LoRa modem. More... | |
| int16_t | beginFSK (float br, float freqDev, float rxBw, uint16_t preambleLength, float tcxoVoltage, bool useRegulatorLDO=false) |
| Initialization method for FSK modem. More... | |
| int16_t | beginLRFHSS (uint8_t bw, uint8_t cr, bool narrowGrid, float tcxoVoltage, bool useRegulatorLDO=false) |
| Initialization method for LR-FHSS modem. This modem only supports transmission! More... | |
| int16_t | setLrFhssConfig (uint8_t bw, uint8_t cr, uint8_t hdrCount=3, uint16_t hopSeqId=0x100) |
| Sets LR-FHSS configuration. More... | |
| int16_t | reset (bool verify=true) |
| Reset method. Will reset the chip to the default state using RST pin. More... | |
| int16_t | transmit (const uint8_t *data, size_t len, uint8_t addr=0) override |
| Blocking binary transmit method. Overloads for string-based transmissions are implemented in PhysicalLayer. More... | |
| int16_t | receive (uint8_t *data, size_t len) override |
| Blocking binary receive method. Overloads for string-based transmissions are implemented in PhysicalLayer. More... | |
| int16_t | transmitDirect (uint32_t frf=0) override |
| Starts direct mode transmission. More... | |
| int16_t | receiveDirect () override |
| Starts direct mode reception. Only implemented for PhysicalLayer compatibility, as SX126x series does not support direct mode reception. Will always return RADIOLIB_ERR_UNKNOWN. More... | |
| int16_t | scanChannel () override |
| Performs scan for LoRa transmission in the current channel. Detects both preamble and payload. Configuration defaults to the values recommended by AN1200.48. More... | |
| int16_t | scanChannel (const ChannelScanConfig_t &config) override |
| Performs scan for LoRa transmission in the current channel. Detects both preamble and payload. More... | |
| int16_t | sleep () override |
| Sets the module to sleep mode. To wake the device up, call standby(). Overload with warm start enabled for PhysicalLayer compatibility. More... | |
| int16_t | sleep (bool retainConfig) |
| Sets the module to sleep mode. To wake the device up, call standby(). More... | |
| int16_t | standby () override |
| Sets the module to standby mode (overload for PhysicalLayer compatibility, uses 13 MHz RC oscillator). More... | |
| int16_t | standby (uint8_t mode, bool wakeup=true) |
| Sets the module to standby mode. More... | |
| void | setDio1Action (void(*func)(void)) |
| Sets interrupt service routine to call when DIO1 activates. More... | |
| void | clearDio1Action () |
| Clears interrupt service routine to call when DIO1 activates. | |
| void | setPacketReceivedAction (void(*func)(void)) override |
| Sets interrupt service routine to call when a packet is received. More... | |
| void | clearPacketReceivedAction () override |
| Clears interrupt service routine to call when a packet is received. | |
| void | setPacketSentAction (void(*func)(void)) override |
| Sets interrupt service routine to call when a packet is sent. More... | |
| void | clearPacketSentAction () override |
| Clears interrupt service routine to call when a packet is sent. | |
| void | setChannelScanAction (void(*func)(void)) override |
| Sets interrupt service routine to call when a channel scan is finished. More... | |
| void | clearChannelScanAction () override |
| Clears interrupt service routine to call when a channel scan is finished. | |
| int16_t | startTransmit (const uint8_t *data, size_t len, uint8_t addr=0) override |
| Interrupt-driven binary transmit method. Overloads for string-based transmissions are implemented in PhysicalLayer. More... | |
| int16_t | finishTransmit () override |
| Clean up after transmission is done. More... | |
| int16_t | startReceive () override |
| Interrupt-driven receive method with default parameters. Implemented for compatibility with PhysicalLayer. More... | |
| int16_t | startReceive (uint32_t timeout, RadioLibIrqFlags_t irqFlags=RADIOLIB_IRQ_RX_DEFAULT_FLAGS, RadioLibIrqFlags_t irqMask=RADIOLIB_IRQ_RX_DEFAULT_MASK, size_t len=0) |
| Interrupt-driven receive method. DIO1 will be activated when full packet is received. More... | |
| int16_t | startReceiveDutyCycle (uint32_t rxPeriod, uint32_t sleepPeriod, RadioLibIrqFlags_t irqFlags=RADIOLIB_IRQ_RX_DEFAULT_FLAGS, RadioLibIrqFlags_t irqMask=RADIOLIB_IRQ_RX_DEFAULT_MASK) |
| Interrupt-driven receive method where the device mostly sleeps and periodically wakes to listen. Note that this function assumes the unit will take 500us + TCXO_delay to change state. See datasheet section 13.1.7, version 1.2. More... | |
| int16_t | startReceiveDutyCycleAuto (uint16_t senderPreambleLength=0, uint16_t minSymbols=8, RadioLibIrqFlags_t irqFlags=RADIOLIB_IRQ_RX_DEFAULT_FLAGS, RadioLibIrqFlags_t irqMask=RADIOLIB_IRQ_RX_DEFAULT_MASK) |
| Calls startReceiveDutyCycle with rxPeriod and sleepPeriod set so the unit shouldn't miss any messages. More... | |
| int16_t | readData (uint8_t *data, size_t len) override |
| Reads data received after calling startReceive method. When the packet length is not known in advance, getPacketLength method must be called BEFORE calling readData! More... | |
| int16_t | startChannelScan () override |
| Interrupt-driven channel activity detection method. DIO1 will be activated when LoRa preamble is detected, or upon timeout. Defaults to CAD parameter values recommended by AN1200.48. More... | |
| int16_t | startChannelScan (const ChannelScanConfig_t &config) override |
| Interrupt-driven channel activity detection method. DIO1 will be activated when LoRa preamble is detected, or upon timeout. More... | |
| int16_t | getChannelScanResult () override |
| Read the channel scan result. More... | |
| int16_t | setBandwidth (float bw) |
| Sets LoRa bandwidth. Allowed values are 7.8, 10.4, 15.6, 20.8, 31.25, 41.7, 62.5, 125.0, 250.0 and 500.0 kHz. More... | |
| int16_t | setSpreadingFactor (uint8_t sf) |
| Sets LoRa spreading factor. Allowed values range from 5 to 12. More... | |
| int16_t | setCodingRate (uint8_t cr) |
| Sets LoRa coding rate denominator. Allowed values range from 5 to 8. More... | |
| int16_t | setSyncWord (uint8_t syncWord, uint8_t controlBits=0x44) |
| Sets LoRa sync word. More... | |
| int16_t | setCurrentLimit (float currentLimit) |
| Sets current protection limit. Can be set in 2.5 mA steps. More... | |
| float | getCurrentLimit () |
| Reads current protection limit. More... | |
| int16_t | setPreambleLength (size_t preambleLength) override |
| Sets preamble length for LoRa or FSK modem. Allowed values range from 1 to 65535. More... | |
| int16_t | setFrequencyDeviation (float freqDev) override |
| Sets FSK frequency deviation. Allowed values range from 0.0 to 200.0 kHz. More... | |
| int16_t | setBitRate (float br) override |
| Sets FSK bit rate. Allowed values range from 0.6 to 300.0 kbps. More... | |
| int16_t | setDataRate (DataRate_t dr) override |
| Set data. More... | |
| int16_t | checkDataRate (DataRate_t dr) override |
| Check the data rate can be configured by this module. More... | |
| int16_t | setRxBandwidth (float rxBw) |
| Sets FSK receiver bandwidth. Allowed values are 4.8, 5.8, 7.3, 9.7, 11.7, 14.6, 19.5, 23.4, 29.3, 39.0, 46.9, 58.6, 78.2, 93.8, 117.3, 156.2, 187.2, 234.3, 312.0, 373.6 and 467.0 kHz. More... | |
| int16_t | setRxBoostedGainMode (bool rxbgm, bool persist=true) |
| Enables or disables Rx Boosted Gain mode as described in SX126x datasheet section 9.6 (SX1261/2 v2.1, SX1268 v1.1) More... | |
| int16_t | setDataShaping (uint8_t sh) override |
| Sets time-bandwidth product of Gaussian filter applied for shaping. Allowed values are RADIOLIB_SHAPING_0_3, RADIOLIB_SHAPING_0_5, RADIOLIB_SHAPING_0_7 or RADIOLIB_SHAPING_1_0. Set to RADIOLIB_SHAPING_NONE to disable data shaping. More... | |
| int16_t | setSyncWord (uint8_t *syncWord, size_t len) override |
| Sets FSK sync word in the form of array of up to 8 bytes. Can also set LR-FHSS sync word, but its length must be 4 bytes. More... | |
| int16_t | setSyncBits (uint8_t *syncWord, uint8_t bitsLen) |
| Sets FSK sync word in the form of array of up to 8 bytes. More... | |
| int16_t | setNodeAddress (uint8_t addr) |
| Sets node address. Calling this method will also enable address filtering for node address only. More... | |
| int16_t | setBroadcastAddress (uint8_t broadAddr) |
| Sets broadcast address. Calling this method will also enable address filtering for node and broadcast address. More... | |
| int16_t | disableAddressFiltering () |
| Disables address filtering. Calling this method will also erase previously set addresses. More... | |
| int16_t | setCRC (uint8_t len, uint16_t initial=0x1D0F, uint16_t polynomial=0x1021, bool inverted=true) |
| Sets CRC configuration. More... | |
| int16_t | setWhitening (bool enabled, uint16_t initial=0x01FF) |
| Sets FSK whitening parameters. More... | |
| int16_t | setTCXO (float voltage, uint32_t delay=5000) |
| Sets TCXO (Temperature Compensated Crystal Oscillator) configuration. More... | |
| int16_t | setDio2AsRfSwitch (bool enable=true) |
| Set DIO2 to function as RF switch (default in Semtech example designs). More... | |
| float | getDataRate () const |
| Gets effective data rate for the last transmitted packet. The value is calculated only for payload bytes. More... | |
| float | getRSSI () override |
| Gets recorded signal strength indicator. Overload with packet mode enabled for PhysicalLayer compatibility. More... | |
| float | getRSSI (bool packet) |
| Gets RSSI (Recorded Signal Strength Indicator). More... | |
| float | getSNR () override |
| Gets SNR (Signal to Noise Ratio) of the last received packet. Only available for LoRa modem. More... | |
| float | getFrequencyError () |
| Gets frequency error of the latest received packet. WARNING: This functionality is based on SX128x implementation and not documented on SX126x. While it seems to be working, it should be used with caution! More... | |
| size_t | getPacketLength (bool update=true) override |
| Query modem for the packet length of received payload. More... | |
| size_t | getPacketLength (bool update, uint8_t *offset) |
| Query modem for the packet length of received payload and Rx buffer offset. More... | |
| int16_t | fixedPacketLengthMode (uint8_t len=RADIOLIB_SX126X_MAX_PACKET_LENGTH) |
| Set modem in fixed packet length mode. Available in FSK mode only. More... | |
| int16_t | variablePacketLengthMode (uint8_t maxLen=RADIOLIB_SX126X_MAX_PACKET_LENGTH) |
| Set modem in variable packet length mode. Available in FSK mode only. More... | |
| RadioLibTime_t | getTimeOnAir (size_t len) override |
| Get expected time-on-air for a given size of payload. More... | |
| RadioLibTime_t | calculateRxTimeout (RadioLibTime_t timeoutUs) override |
| Calculate the timeout value for this specific module / series (in number of symbols or units of time) More... | |
| uint32_t | getIrqFlags () override |
| Read currently active IRQ flags. More... | |
| int16_t | setIrqFlags (uint32_t irq) override |
| Set interrupt on DIO1 to be sent on a specific IRQ bit (e.g. RxTimeout, CadDone). More... | |
| int16_t | clearIrqFlags (uint32_t irq) override |
| Clear interrupt on a specific IRQ bit (e.g. RxTimeout, CadDone). More... | |
| int16_t | implicitHeader (size_t len) |
| Set implicit header mode for future reception/transmission. More... | |
| int16_t | explicitHeader () |
| Set explicit header mode for future reception/transmission. More... | |
| int16_t | setRegulatorLDO () |
| Set regulator mode to LDO. More... | |
| int16_t | setRegulatorDCDC () |
| Set regulator mode to DC-DC. More... | |
| int16_t | setEncoding (uint8_t encoding) override |
| Sets transmission encoding. Available in FSK mode only. Serves only as alias for PhysicalLayer compatibility. More... | |
| void | setRfSwitchPins (uint32_t rxEn, uint32_t txEn) |
Some modules contain external RF switch controlled by pins. This function gives RadioLib control over those pins to automatically switch between various modes: When idle both pins will be LOW, during TX the txEn pin will be HIGH, during RX the rxPin will be HIGH. More... | |
| void | setRfSwitchTable (const uint32_t(&pins)[Module::RFSWITCH_MAX_PINS], const Module::RfSwitchMode_t table[]) |
| Some modules contain external RF switch controlled by pins. This function gives RadioLib control over those pins to automatically switch between various modes. More... | |
| int16_t | forceLDRO (bool enable) |
| Forces LoRa low data rate optimization. Only available in LoRa mode. After calling this method, LDRO will always be set to the provided value, regardless of symbol length. To re-enable automatic LDRO configuration, call SX126x::autoLDRO() More... | |
| int16_t | autoLDRO () |
| Re-enables automatic LDRO configuration. Only available in LoRa mode. After calling this method, LDRO will be enabled automatically when symbol length exceeds 16 ms. More... | |
| uint8_t | randomByte () override |
| Get one truly random byte from RSSI noise. More... | |
| int16_t | invertIQ (bool enable) override |
| Enable/disable inversion of the I and Q signals. More... | |
| int16_t | getModem (ModemType_t *modem) override |
| Get modem currently in use by the radio. More... | |
| void | setDirectAction (void(*func)(void)) override |
| Set interrupt service routine function to call when data bit is received in direct mode. More... | |
| void | readBit (uint32_t pin) override |
| Function to read and process data bit in direct reception mode. More... | |
| int16_t | uploadPatch (const uint32_t *patch, size_t len, bool nonvolatile=true) |
| Upload binary patch into the SX126x device RAM. Patch is needed to e.g., enable spectral scan and must be uploaded again on every power cycle. More... | |
| int16_t | spectralScanStart (uint16_t numSamples, uint8_t window=RADIOLIB_SX126X_SPECTRAL_SCAN_WINDOW_DEFAULT, uint8_t interval=RADIOLIB_SX126X_SCAN_INTERVAL_8_20_US) |
| Start spectral scan. Requires binary path to be uploaded. More... | |
| void | spectralScanAbort () |
| Abort an ongoing spectral scan. | |
| int16_t | spectralScanGetStatus () |
| Read the status of spectral scan. More... | |
| int16_t | spectralScanGetResult (uint16_t *results) |
| Read the result of spectral scan. More... | |
| int16_t | setPaConfig (uint8_t paDutyCycle, uint8_t deviceSel, uint8_t hpMax=RADIOLIB_SX126X_PA_CONFIG_HP_MAX, uint8_t paLut=RADIOLIB_SX126X_PA_CONFIG_PA_LUT) |
| Set the PA configuration. Allows user to optimize PA for a specific output power and matching network. Any calls to this method must be done after calling begin/beginFSK and/or setOutputPower. WARNING: Use at your own risk! Setting invalid values can and will lead to permanent damage! More... | |
| int16_t | calibrateImage (float freq) |
| Perform image rejection calibration for the specified frequency. Will try to use Semtech-defined presets first, and if none of them matches, custom iamge calibration will be attempted using calibrateImageRejection. More... | |
| int16_t | calibrateImageRejection (float freqMin, float freqMax) |
| Perform image rejection calibration for the specified frequency band. WARNING: Use at your own risk! Setting incorrect values may lead to decreased performance. More... | |
| int16_t | setPaRampTime (uint8_t rampTime) |
| Set PA ramp-up time. Set to 200us by default. More... | |
| int16_t | transmit (const char *str, uint8_t addr=0) |
| C-string transmit method. More... | |
| virtual int16_t | transmit (const uint8_t *data, size_t len, uint8_t addr=0) |
| Binary transmit method. Must be implemented in module class. More... | |
| virtual int16_t | receive (uint8_t *data, size_t len) |
| Binary receive method. Must be implemented in module class. More... | |
| int16_t | startTransmit (const char *str, uint8_t addr=0) |
| Interrupt-driven Arduino String transmit method. Unlike the standard transmit method, this one is non-blocking. Interrupt pin will be activated when transmission finishes. More... | |
| virtual int16_t | startTransmit (const uint8_t *data, size_t len, uint8_t addr=0) |
| Interrupt-driven binary transmit method. More... | |
| virtual int16_t | readData (uint8_t *data, size_t len) |
| Reads data that was received after calling startReceive method. More... | |
| Public Member Functions inherited from PhysicalLayer | |
| PhysicalLayer (float step, size_t maxLen) | |
| Default constructor. More... | |
| int16_t | transmit (const char *str, uint8_t addr=0) |
| C-string transmit method. More... | |
| virtual int16_t | standby (uint8_t mode) |
| Sets module to a specific standby mode. More... | |
| int16_t | startTransmit (const char *str, uint8_t addr=0) |
| Interrupt-driven Arduino String transmit method. Unlike the standard transmit method, this one is non-blocking. Interrupt pin will be activated when transmission finishes. More... | |
| float | getFreqStep () const |
| Gets the module frequency step size that was set in constructor. More... | |
| uint32_t | getIrqMapped (RadioLibIrqFlags_t irq) |
| Convert from radio-agnostic IRQ flags to radio-specific flags. More... | |
| int16_t | checkIrq (RadioLibIrqType_t irq) |
| Check whether a specific IRQ bit is set (e.g. RxTimeout, CadDone). More... | |
| int16_t | setIrq (RadioLibIrqFlags_t irq) |
| Set interrupt on specific IRQ bit(s) (e.g. RxTimeout, CadDone). Keep in mind that not all radio modules support all RADIOLIB_IRQ_ flags! More... | |
| int16_t | clearIrq (RadioLibIrqFlags_t irq) |
| Clear interrupt on a specific IRQ bit (e.g. RxTimeout, CadDone). Keep in mind that not all radio modules support all RADIOLIB_IRQ_ flags! More... | |
| int32_t | random (int32_t max) |
| Get truly random number in range 0 - max. More... | |
| int32_t | random (int32_t min, int32_t max) |
| Get truly random number in range min - max. More... | |
| int16_t | startDirect () |
| Configure module parameters for direct modes. Must be called prior to "ham" modes like RTTY or AX.25. Only available in FSK mode. More... | |
| int16_t | setDirectSyncWord (uint32_t syncWord, uint8_t len) |
| Set sync word to be used to determine start of packet in direct reception mode. More... | |
| int16_t | available () |
| Get the number of direct mode bytes currently available in buffer. More... | |
| void | dropSync () |
| Forcefully drop synchronization. | |
| uint8_t | read (bool drop=true) |
| Get data from direct mode buffer. More... | |
| virtual int16_t | setDIOMapping (uint32_t pin, uint32_t value) |
| Configure DIO pin mapping to get a given signal on a DIO pin (if available). More... | |
Additional Inherited Members | |
| Public Attributes inherited from SX126x | |
| bool | XTAL |
| Whether the module has an XTAL (true) or TCXO (false). Defaults to false. | |
| bool | standbyXOSC |
| Whether to use XOSC (true) or RC (false) oscillator in standby mode. Defaults to false. | |
Detailed Description
Derived class for SX1261 modules.
Constructor & Destructor Documentation
◆ SX1261()
| SX1261::SX1261 | ( | Module * | mod | ) |
Default constructor.
- Parameters
-
mod Instance of Module that will be used to communicate with the radio.
Member Function Documentation
◆ checkOutputPower()
|
overridevirtual |
Check if output power is configurable.
- Parameters
-
power Output power in dBm. clipped Clipped output power value to what is possible within the module's range.
- Returns
- Status Codes
Reimplemented from PhysicalLayer.
◆ setOutputPower()
|
overridevirtual |
Sets output power. Allowed values are in range from -17 to 15 dBm.
- Parameters
-
power Output power to be set in dBm.
- Returns
- Status Codes
Reimplemented from SX1262.
The documentation for this class was generated from the following files:
- src/modules/SX126x/SX1261.h
- src/modules/SX126x/SX1261.cpp
