Derived class for SX1277 modules. Overrides some methods from SX1278 due to different parameter ranges. More...

#include <SX1277.h>

Inheritance diagram for SX1277:

Public Member Functions
	SX1277 (Module *mod)
	Default constructor. Called from Arduino sketch when creating new LoRa instance. More...

int16_t	begin (float freq=434.0, float bw=125.0, uint8_t sf=9, uint8_t cr=7, uint8_t syncWord=RADIOLIB_SX127X_SYNC_WORD, int8_t power=10, uint16_t preambleLength=8, uint8_t gain=0)
	LoRa modem initialization method. Must be called at least once from Arduino sketch to initialize the module. More...

int16_t	beginFSK (float freq=434.0, float br=4.8, float freqDev=5.0, float rxBw=125.0, int8_t power=10, uint16_t preambleLength=16, bool enableOOK=false)
	FSK modem initialization method. Must be called at least once from Arduino sketch to initialize the module. More...

int16_t	setFrequency (float freq) override
	Sets carrier frequency. Allowed values range from 137.0 MHz to 1020.0 MHz. More...

int16_t	setSpreadingFactor (uint8_t sf)
	Sets LoRa link spreading factor. Allowed values range from 6 to 9. Only available in LoRa mode. More...

int16_t	setDataRate (DataRate_t dr) override
	Set data. More...

int16_t	checkDataRate (DataRate_t dr) override
	Check the data rate can be configured by this module. More...

int16_t	setModem (ModemType_t modem) override
	Set modem for the radio to use. Will perform full reset and reconfigure the radio using its default parameters. More...

Public Member Functions inherited from SX1278
	SX1278 (Module *mod)
	Default constructor. Called from Arduino sketch when creating new LoRa instance. More...

int16_t	begin (float freq=434.0, float bw=125.0, uint8_t sf=9, uint8_t cr=7, uint8_t syncWord=RADIOLIB_SX127X_SYNC_WORD, int8_t power=10, uint16_t preambleLength=8, uint8_t gain=0)
	LoRa modem initialization method. Must be called at least once from Arduino sketch to initialize the module. More...

int16_t	beginFSK (float freq=434.0, float br=4.8, float freqDev=5.0, float rxBw=125.0, int8_t power=10, uint16_t preambleLength=16, bool enableOOK=false)
	FSK modem initialization method. Must be called at least once from Arduino sketch to initialize the module. More...

void	reset () override
	Reset method. Will reset the chip to the default state using RST pin.

int16_t	setFrequency (float freq) override
	Sets carrier frequency. Allowed values range from 137.0 MHz to 525.0 MHz. More...

int16_t	setBandwidth (float bw)
	Sets LoRa link bandwidth. Allowed values are 10.4, 15.6, 20.8, 31.25, 41.7, 62.5, 125, 250 and 500 kHz. Only available in LoRa mode. More...

int16_t	setSpreadingFactor (uint8_t sf)
	Sets LoRa link spreading factor. Allowed values range from 6 to 12. Only available in LoRa mode. More...

int16_t	setCodingRate (uint8_t cr)
	Sets LoRa link coding rate denominator. Allowed values range from 5 to 8. Only available in LoRa mode. More...

int16_t	setBitRate (float br) override
	Sets FSK bit rate. Allowed values range from 0.5 to 300 kbps. Only available in FSK mode. More...

int16_t	setDataRate (DataRate_t dr) override
	Set data. More...

int16_t	checkDataRate (DataRate_t dr) override
	Check the data rate can be configured by this module. More...

int16_t	setOutputPower (int8_t power) override
	Sets transmission output power. Allowed values range from -3 to 15 dBm (RFO pin) or +2 to +17 dBm (PA_BOOST pin). High power +20 dBm operation is also supported, on the PA_BOOST pin. Defaults to PA_BOOST. More...

int16_t	setOutputPower (int8_t power, bool useRfo)
	Sets transmission output power. Allowed values range from -3 to 15 dBm (RFO pin) or +2 to +17 dBm (PA_BOOST pin). High power +20 dBm operation is also supported, on the PA_BOOST pin. More...

int16_t	checkOutputPower (int8_t power, int8_t *clipped) override
	Check if output power is configurable. This method is needed for compatibility with PhysicalLayer::checkOutputPower. More...

int16_t	checkOutputPower (int8_t power, int8_t *clipped, bool useRfo)
	Check if output power is configurable. More...

int16_t	setGain (uint8_t gain)
	Sets gain of receiver LNA (low-noise amplifier). Can be set to any integer in range 1 to 6 where 1 is the highest gain. Set to 0 to enable automatic gain control (recommended). More...

int16_t	setDataShaping (uint8_t sh) override
	Sets Gaussian filter bandwidth-time product that will be used for data shaping. Only available in FSK mode with FSK modulation. Allowed values are RADIOLIB_SHAPING_0_3, RADIOLIB_SHAPING_0_5 or RADIOLIB_SHAPING_1_0. Set to RADIOLIB_SHAPING_NONE to disable data shaping. More...

int16_t	setDataShapingOOK (uint8_t sh)
	Sets filter cutoff frequency that will be used for data shaping. Allowed values are 1 for frequency equal to bit rate and 2 for frequency equal to 2x bit rate. Set to 0 to disable data shaping. Only available in FSK mode with OOK modulation. More...

float	getRSSI () override
	Gets recorded signal strength indicator. Overload with packet mode enabled for PhysicalLayer compatibility. More...

float	getRSSI (bool packet, bool skipReceive=false)
	Gets recorded signal strength indicator. More...

int16_t	setCRC (bool enable, bool mode=false)
	Enables/disables CRC check of received packets. More...

int16_t	forceLDRO (bool enable)
	Forces LoRa low data rate optimization. Only available in LoRa mode. After calling this method, LDRO will always be set to the provided value, regardless of symbol length. To re-enable automatic LDRO configuration, call SX1278::autoLDRO() More...

int16_t	autoLDRO ()
	Re-enables automatic LDRO configuration. Only available in LoRa mode. After calling this method, LDRO will be enabled automatically when symbol length exceeds 16 ms. More...

int16_t	implicitHeader (size_t len)
	Set implicit header mode for future reception/transmission. Required for spreading factor 6. More...

int16_t	explicitHeader ()
	Set explicit header mode for future reception/transmission. More...

int16_t	setModem (ModemType_t modem) override
	Set modem for the radio to use. Will perform full reset and reconfigure the radio using its default parameters. More...

Public Member Functions inherited from SX127x
	SX127x (Module *mod)
	Default constructor. Called internally when creating new LoRa instance. More...

int16_t	begin (uint8_t *chipVersions, uint8_t numVersions, uint8_t syncWord, uint16_t preambleLength)
	Initialization method. Will be called with appropriate parameters when calling initialization method from derived class. More...

int16_t	beginFSK (uint8_t *chipVersions, uint8_t numVersions, float freqDev, float rxBw, uint16_t preambleLength, bool enableOOK)
	Initialization method for FSK modem. Will be called with appropriate parameters when calling FSK initialization method from derived class. More...

int16_t	transmit (const uint8_t *data, size_t len, uint8_t addr=0) override
	Binary transmit method. Will transmit arbitrary binary data up to 255 bytes long using LoRa or up to 63 bytes using FSK modem. For overloads to transmit Arduino String or C-string, see PhysicalLayer::transmit. More...

int16_t	receive (uint8_t *data, size_t len) override
	Binary receive method. Will attempt to receive arbitrary binary data up to 255 bytes long using LoRa or up to 63 bytes using FSK modem. For overloads to receive Arduino String, see PhysicalLayer::receive. More...

int16_t	scanChannel () override
	Performs scan for valid LoRa preamble in the current channel. More...

int16_t	sleep () override
	Sets the LoRa module to sleep to save power. Module will not be able to transmit or receive any data while in sleep mode. Module will wake up automatically when methods like transmit or receive are called. More...

int16_t	standby () override
	Sets the LoRa module to standby. More...

int16_t	standby (uint8_t mode) override
	Sets the LoRa module to standby. More...

int16_t	transmitDirect (uint32_t frf=0) override
	Enables direct transmission mode on pins DIO1 (clock) and DIO2 (data). While in direct mode, the module will not be able to transmit or receive packets. Can only be activated in FSK mode. More...

int16_t	receiveDirect () override
	Enables direct reception mode on pins DIO1 (clock) and DIO2 (data). While in direct mode, the module will not be able to transmit or receive packets. Can only be activated in FSK mode. More...

int16_t	packetMode ()
	Disables direct mode and enables packet mode, allowing the module to receive packets. Can only be activated in FSK mode. More...

void	setDio0Action (void(*func)(void), uint32_t dir)
	Set interrupt service routine function to call when DIO0 activates. More...

void	clearDio0Action ()
	Clears interrupt service routine to call when DIO0 activates.

void	setDio1Action (void(*func)(void), uint32_t dir)
	Set interrupt service routine function to call when DIO1 activates. More...

void	clearDio1Action ()
	Clears interrupt service routine to call when DIO1 activates.

void	setPacketReceivedAction (void(*func)(void)) override
	Sets interrupt service routine to call when a packet is received. More...

void	clearPacketReceivedAction () override
	Clears interrupt service routine to call when a packet is received.

void	setPacketSentAction (void(*func)(void)) override
	Sets interrupt service routine to call when a packet is sent. More...

void	clearPacketSentAction () override
	Clears interrupt service routine to call when a packet is sent.

void	setChannelScanAction (void(*func)(void)) override
	Sets interrupt service routine to call when a channel scan is finished. More...

void	clearChannelScanAction () override
	Clears interrupt service routine to call when a channel scan is finished.

void	setFifoEmptyAction (void(*func)(void))
	Set interrupt service routine function to call when FIFO is empty. More...

void	clearFifoEmptyAction ()
	Clears interrupt service routine to call when FIFO is empty.

void	setFifoThreshold (uint8_t threshold)
	Set FIFO threshold level. Be aware that threshold is also set in setFifoFullAction method. setFifoThreshold method must be called AFTER calling setFifoFullAction! More...

void	setFifoFullAction (void(*func)(void))
	Set interrupt service routine function to call when FIFO is full. More...

void	clearFifoFullAction ()
	Clears interrupt service routine to call when FIFO is full.

bool	fifoAdd (uint8_t data, int totalLen, int remLen)
	Set interrupt service routine function to call when FIFO is empty. More...

bool	fifoGet (volatile uint8_t data, int totalLen, volatile int rcvLen)
	Set interrupt service routine function to call when FIFO is sufficiently full to read. More...

int16_t	startTransmit (const uint8_t *data, size_t len, uint8_t addr=0) override
	Interrupt-driven binary transmit method. Will start transmitting arbitrary binary data up to 255 bytes long using LoRa or up to 63 bytes using FSK modem. More...

int16_t	finishTransmit () override
	Clean up after transmission is done. More...

int16_t	startReceive () override
	Interrupt-driven receive method with default parameters. Implemented for compatibility with PhysicalLayer. More...

int16_t	startReceive (uint32_t timeout, RadioLibIrqFlags_t irqFlags=RADIOLIB_IRQ_RX_DEFAULT_FLAGS, RadioLibIrqFlags_t irqMask=RADIOLIB_IRQ_RX_DEFAULT_MASK, size_t len=0) override
	Interrupt-driven receive method, implemented for compatibility with PhysicalLayer. More...

int16_t	readData (uint8_t *data, size_t len) override
	Reads data that was received after calling startReceive method. When the packet length is not known in advance, getPacketLength method must be called BEFORE calling readData! More...

int16_t	startChannelScan () override
	Interrupt-driven channel activity detection method. DIO0 will be activated when LoRa preamble is detected. DIO1 will be activated if there's no preamble detected before timeout. More...

int16_t	getChannelScanResult () override
	Read the channel scan result. More...

int16_t	setSyncWord (uint8_t syncWord)
	Sets LoRa sync word. Only available in LoRa mode. More...

int16_t	setCurrentLimit (uint8_t currentLimit)
	Sets current limit for over current protection at transmitter amplifier. Allowed values range from 45 to 120 mA in 5 mA steps and 120 to 240 mA in 10 mA steps. More...

int16_t	setPreambleLength (size_t preambleLength) override
	Sets LoRa or FSK preamble length. Allowed values range from 6 to 65535 in LoRa mode or 0 to 65535 in FSK mode. More...

int16_t	invertPreamble (bool enable)
	Invert FSK preamble polarity. The default (non-inverted) is 0x55, the inverted is 0xAA. More...

float	getFrequencyError (bool autoCorrect=false)
	Gets frequency error of the latest received packet. More...

float	getAFCError ()
	Gets current AFC error. More...

float	getSNR () override
	Gets signal-to-noise ratio of the latest received packet. Only available in LoRa mode. More...

float	getDataRate () const
	Get data rate of the latest transmitted packet. More...

int16_t	setFrequencyDeviation (float freqDev) override
	Sets FSK frequency deviation from carrier frequency. Allowed values depend on bit rate setting and must be lower than 200 kHz. Only available in FSK mode. More...

int16_t	setRxBandwidth (float rxBw)
	Sets FSK receiver bandwidth. Allowed values range from 2.6 to 250 kHz. Only available in FSK mode. More...

int16_t	setAFCBandwidth (float afcBw)
	Sets FSK automatic frequency correction bandwidth. Allowed values range from 2.6 to 250 kHz. Only available in FSK mode. More...

int16_t	setAFC (bool isEnabled)
	Enables or disables FSK automatic frequency correction(AFC) More...

int16_t	setAFCAGCTrigger (uint8_t trigger)
	Controls trigger of AFC and AGC. More...

int16_t	setSyncWord (uint8_t *syncWord, size_t len) override
	Sets FSK sync word. Allowed sync words are up to 8 bytes long and can not contain null bytes. Only available in FSK mode. More...

int16_t	setNodeAddress (uint8_t nodeAddr)
	Sets FSK node address. Calling this method will enable address filtering. Only available in FSK mode. More...

int16_t	setBroadcastAddress (uint8_t broadAddr)
	Sets FSK broadcast address. Calling this method will enable address filtering. Only available in FSK mode. More...

int16_t	disableAddressFiltering ()
	Disables FSK address filtering. More...

int16_t	setOOK (bool enableOOK)
	Enables/disables OOK modulation instead of FSK. More...

int16_t	setOokThresholdType (uint8_t type)
	Selects the type of threshold in the OOK data slicer. More...

int16_t	setOokPeakThresholdDecrement (uint8_t value)
	Period of decrement of the RSSI threshold in the OOK demodulator. More...

int16_t	setOokFixedOrFloorThreshold (uint8_t value)
	Fixed threshold for the Data Slicer in OOK mode or floor threshold for the Data Slicer in OOK when Peak mode is used. More...

int16_t	setOokPeakThresholdStep (uint8_t value)
	Size of each decrement of the RSSI threshold in the OOK demodulator. More...

int16_t	enableBitSync ()
	Enable Bit synchronizer. More...

int16_t	disableBitSync ()
	Disable Bit synchronizer (not allowed in Packet mode). More...

size_t	getPacketLength (bool update=true) override
	Query modem for the packet length of received payload. More...

int16_t	fixedPacketLengthMode (uint8_t len=RADIOLIB_SX127X_MAX_PACKET_LENGTH_FSK)
	Set modem in fixed packet length mode. Available in FSK mode only. More...

int16_t	variablePacketLengthMode (uint8_t maxLen=RADIOLIB_SX127X_MAX_PACKET_LENGTH_FSK)
	Set modem in variable packet length mode. Available in FSK mode only. More...

float	getNumSymbols (size_t len)
	Convert from bytes to LoRa symbols. More...

RadioLibTime_t	getTimeOnAir (size_t len) override
	Get expected time-on-air for a given size of payload. More...

RadioLibTime_t	calculateRxTimeout (RadioLibTime_t timeoutUs) override
	Calculate the timeout value for this specific module / series (in number of symbols or units of time) More...

uint32_t	getIrqFlags () override
	Read currently active IRQ flags. More...

int16_t	setIrqFlags (uint32_t irq) override
	Set interrupt on DIO1 to be sent on a specific IRQ bit (e.g. RxTimeout, CadDone). NOTE: Unlike other modules that support IRQ abstraction (SX126x, LR11x0, etc.), SX127x cannot configure multiple IRQs to signal using the same DIOx pin. This method tries to configure IRQs in a "best effort" approach, and will skip conflicting flags. RADIOLIB_ERR_INVALID_IRQ will be returned in this case. More...

int16_t	clearIrqFlags (uint32_t irq) override
	Clear interrupt on a specific IRQ bit (e.g. RxTimeout, CadDone). More...

int16_t	setCrcFiltering (bool enable=true)
	Enable CRC filtering and generation. More...

int16_t	setRSSIConfig (uint8_t smoothingSamples, int8_t offset=0)
	Sets RSSI measurement configuration in FSK mode. More...

int16_t	setEncoding (uint8_t encoding) override
	Sets transmission encoding. Only available in FSK mode. Allowed values are RADIOLIB_ENCODING_NRZ, RADIOLIB_ENCODING_MANCHESTER and RADIOLIB_ENCODING_WHITENING. More...

uint16_t	getIRQFlags ()
	Reads currently active IRQ flags, can be used to check which event caused an interrupt. In LoRa mode, this is the content of SX127X_REG_IRQ_FLAGS register. In FSK mode, this is the contents of SX127X_REG_IRQ_FLAGS_2 (MSB) and SX127X_REG_IRQ_FLAGS_1 (LSB) registers. More...

uint8_t	getModemStatus ()
	Reads modem status. Only available in LoRa mode. More...

int8_t	getTempRaw ()
	Reads uncalibrated temperature value. This function will change operating mode and should not be called during Tx, Rx or CAD. More...

void	setRfSwitchPins (uint32_t rxEn, uint32_t txEn)
	Some modules contain external RF switch controlled by pins. This function gives RadioLib control over those pins to automatically switch between various modes: When idle both pins will be LOW, during TX the `txEn` pin will be HIGH, during RX the `rxPin` will be HIGH. More...

void	setRfSwitchTable (const uint32_t(&pins)[Module::RFSWITCH_MAX_PINS], const Module::RfSwitchMode_t table[])
	Some modules contain external RF switch controlled by pins. This function gives RadioLib control over those pins to automatically switch between various modes. More...

uint8_t	randomByte () override
	Get one truly random byte from RSSI noise. More...

int16_t	getChipVersion ()
	Read version SPI register. Should return SX1278_CHIP_VERSION (0x12) or SX1272_CHIP_VERSION (0x22) if SX127x is connected and working. More...

int16_t	invertIQ (bool enable) override
	Enable/disable inversion of the I and Q signals. More...

int16_t	getModem (ModemType_t *modem) override
	Get modem currently in use by the radio. More...

void	setDirectAction (void(*func)(void)) override
	Set interrupt service routine function to call when data bit is received in direct mode. More...

void	readBit (uint32_t pin) override
	Function to read and process data bit in direct reception mode. More...

int16_t	setFHSSHoppingPeriod (uint8_t freqHoppingPeriod)
	Sets the hopping period and enables FHSS. More...

uint8_t	getFHSSHoppingPeriod (void)
	Gets FHSS hopping period. More...

uint8_t	getFHSSChannel (void)
	Gets the FHSS channel in use. More...

void	clearFHSSInt (void)
	Clear the FHSS interrupt.

int16_t	setDIOMapping (uint32_t pin, uint32_t value) override
	Configure DIO pin mapping to get a given signal on a DIO pin (if available). More...

int16_t	setDIOPreambleDetect (bool usePreambleDetect)
	Configure DIO mapping to use RSSI or Preamble Detect for pins that support it. More...

int16_t	setRSSIThreshold (float dbm)
	Sets the RSSI value above which the RSSI interrupt is signaled. More...

int16_t	setLowBatteryThreshold (int8_t level, uint32_t pin=RADIOLIB_NC)
	Set low battery indicator threshold. More...

int16_t	transmit (const char *str, uint8_t addr=0)
	C-string transmit method. More...

virtual int16_t	transmit (const uint8_t *data, size_t len, uint8_t addr=0)
	Binary transmit method. Must be implemented in module class. More...

virtual int16_t	receive (uint8_t *data, size_t len)
	Binary receive method. Must be implemented in module class. More...

int16_t	startTransmit (const char *str, uint8_t addr=0)
	Interrupt-driven Arduino String transmit method. Unlike the standard transmit method, this one is non-blocking. Interrupt pin will be activated when transmission finishes. More...

virtual int16_t	startTransmit (const uint8_t *data, size_t len, uint8_t addr=0)
	Interrupt-driven binary transmit method. More...

virtual int16_t	readData (uint8_t *data, size_t len)
	Reads data that was received after calling startReceive method. More...

Public Member Functions inherited from PhysicalLayer
	PhysicalLayer (float step, size_t maxLen)
	Default constructor. More...

int16_t	transmit (const char *str, uint8_t addr=0)
	C-string transmit method. More...

int16_t	startTransmit (const char *str, uint8_t addr=0)
	Interrupt-driven Arduino String transmit method. Unlike the standard transmit method, this one is non-blocking. Interrupt pin will be activated when transmission finishes. More...

float	getFreqStep () const
	Gets the module frequency step size that was set in constructor. More...

uint32_t	getIrqMapped (RadioLibIrqFlags_t irq)
	Convert from radio-agnostic IRQ flags to radio-specific flags. More...

int16_t	checkIrq (RadioLibIrqType_t irq)
	Check whether a specific IRQ bit is set (e.g. RxTimeout, CadDone). More...

int16_t	setIrq (RadioLibIrqFlags_t irq)
	Set interrupt on specific IRQ bit(s) (e.g. RxTimeout, CadDone). Keep in mind that not all radio modules support all RADIOLIB_IRQ_ flags! More...

int16_t	clearIrq (RadioLibIrqFlags_t irq)
	Clear interrupt on a specific IRQ bit (e.g. RxTimeout, CadDone). Keep in mind that not all radio modules support all RADIOLIB_IRQ_ flags! More...

virtual int16_t	startChannelScan (const ChannelScanConfig_t &config)
	Interrupt-driven channel activity detection method. interrupt will be activated when packet is detected. Must be implemented in module class. More...

virtual int16_t	scanChannel (const ChannelScanConfig_t &config)
	Check whether the current communication channel is free or occupied. Performs CAD for LoRa modules, or RSSI measurement for FSK modules. More...

int32_t	random (int32_t max)
	Get truly random number in range 0 - max. More...

int32_t	random (int32_t min, int32_t max)
	Get truly random number in range min - max. More...

int16_t	startDirect ()
	Configure module parameters for direct modes. Must be called prior to "ham" modes like RTTY or AX.25. Only available in FSK mode. More...

int16_t	setDirectSyncWord (uint32_t syncWord, uint8_t len)
	Set sync word to be used to determine start of packet in direct reception mode. More...

int16_t	available ()
	Get the number of direct mode bytes currently available in buffer. More...

void	dropSync ()
	Forcefully drop synchronization.

uint8_t	read (bool drop=true)
	Get data from direct mode buffer. More...

Detailed Description

Derived class for SX1277 modules. Overrides some methods from SX1278 due to different parameter ranges.

Constructor & Destructor Documentation

◆ SX1277()

SX1277::SX1277 ( Module * mod )

Default constructor. Called from Arduino sketch when creating new LoRa instance.

Parameters

mod	Instance of Module that will be used to communicate with the LoRa chip.

Member Function Documentation

◆ begin()

int16_t SX1277::begin	(	float	freq = `434.0`,
		float	bw = `125.0`,
		uint8_t	sf = `9`,
		uint8_t	cr = `7`,
		uint8_t	syncWord = `RADIOLIB_SX127X_SYNC_WORD`,
		int8_t	power = `10`,
		uint16_t	preambleLength = `8`,
		uint8_t	gain = `0`
	)

LoRa modem initialization method. Must be called at least once from Arduino sketch to initialize the module.

Parameters

freq	Carrier frequency in MHz. Allowed values range from 137.0 MHz to 1020.0 MHz.
bw	LoRa link bandwidth in kHz. Allowed values are 10.4, 15.6, 20.8, 31.25, 41.7, 62.5, 125, 250 and 500 kHz.
sf	LoRa link spreading factor. Allowed values range from 6 to 9.
cr	LoRa link coding rate denominator. Allowed values range from 5 to 8.
syncWord	LoRa sync word. Can be used to distinguish different networks. Note that value 0x34 is reserved for LoRaWAN networks.
power	Transmission output power in dBm. Allowed values range from 2 to 17 dBm.
preambleLength	Length of LoRa transmission preamble in symbols. The actual preamble length is 4.25 symbols longer than the set number. Allowed values range from 6 to 65535.
gain	Gain of receiver LNA (low-noise amplifier). Can be set to any integer in range 1 to 6 where 1 is the highest gain. Set to 0 to enable automatic gain control (recommended).

Returns: Status Codes

◆ beginFSK()

int16_t SX1277::beginFSK	(	float	freq = `434.0`,
		float	br = `4.8`,
		float	freqDev = `5.0`,
		float	rxBw = `125.0`,
		int8_t	power = `10`,
		uint16_t	preambleLength = `16`,
		bool	enableOOK = `false`
	)

FSK modem initialization method. Must be called at least once from Arduino sketch to initialize the module.

Parameters

freq	Carrier frequency in MHz. Allowed values range from 137.0 MHz to 525.0 MHz.
br	Bit rate of the FSK transmission in kbps (kilobits per second). Allowed values range from 1.2 to 300.0 kbps.
freqDev	Frequency deviation of the FSK transmission in kHz. Allowed values range from 0.6 to 200.0 kHz. Note that the allowed range changes based on bit rate setting, so that the condition FreqDev + BitRate/2 <= 250 kHz is always met.
rxBw	Receiver bandwidth in kHz. Allowed values are 2.6, 3.1, 3.9, 5.2, 6.3, 7.8, 10.4, 12.5, 15.6, 20.8, 25, 31.3, 41.7, 50, 62.5, 83.3, 100, 125, 166.7, 200 and 250 kHz.
power	Transmission output power in dBm. Allowed values range from 2 to 17 dBm.
preambleLength	Length of FSK preamble in bits.
enableOOK	Use OOK modulation instead of FSK.

Returns: Status Codes

◆ checkDataRate()

int16_t SX1277::checkDataRate ( DataRate_t dr )

overridevirtual

Check the data rate can be configured by this module.

Parameters

dr	Data rate struct. Interpretation depends on currently active modem (FSK or LoRa).

Returns: Status Codes

Reimplemented from PhysicalLayer.

◆ setDataRate()

int16_t SX1277::setDataRate ( DataRate_t dr )

overridevirtual

Set data.

Parameters

dr	Data rate struct. Interpretation depends on currently active modem (FSK or LoRa).

Returns: Status Codes

Reimplemented from PhysicalLayer.

◆ setFrequency()

int16_t SX1277::setFrequency ( float freq )

overridevirtual

Sets carrier frequency. Allowed values range from 137.0 MHz to 1020.0 MHz.

Parameters

freq	Carrier frequency to be set in MHz.

Returns: Status Codes

Reimplemented from PhysicalLayer.

◆ setModem()

int16_t SX1277::setModem ( ModemType_t modem )

overridevirtual

Set modem for the radio to use. Will perform full reset and reconfigure the radio using its default parameters.

Parameters

modem Modem type to set - FSK or LoRa.

Returns: Status Codes

Reimplemented from PhysicalLayer.

◆ setSpreadingFactor()

int16_t SX1277::setSpreadingFactor ( uint8_t sf )

Sets LoRa link spreading factor. Allowed values range from 6 to 9. Only available in LoRa mode.

Parameters

sf	LoRa link spreading factor to be set.

Returns: Status Codes

The documentation for this class was generated from the following files:

src/modules/SX127x/SX1277.h
src/modules/SX127x/SX1277.cpp

Public Member Functions

Detailed Description

Constructor & Destructor Documentation

◆ SX1277()

Member Function Documentation

◆ begin()

◆ beginFSK()

◆ checkDataRate()

◆ setDataRate()

◆ setFrequency()

◆ setModem()

◆ setSpreadingFactor()